A. Cast Crank Flywheel
Replacement flywheel for the 360 cast crank engine with external balance. Not SFI approved. It is 6-bolt for 10 1/2" clutch.
P4529110 Cast Crank Flywheel-130 Tooth (1971–92 360 Small Block, not AMC 360)
B. Race Steel Flywheel
This race steel V8 flywheel weighs 18 1/2 lbs. and is designed for use with 10 1/2" clutch.
*P4876047 Race Steel Flywheel-6-Bolt (Big Block, Small Block)
C. Steel Replacement Flywheels
Steel Replacement Flywheels weigh 30 lbs. and are for use with 10 1/2" clutch. Not SFI approved.
P4529142 Steel Flywheel-6-Bolt, 130 Tooth (Big Block, Small Block)
P4529143 Steel Flywheel-8-Bolt, 130 Tooth (Big Block, Small Block)
D. Flywheel Attaching Screw Set
This flywheel attaching screw set is ideal for inline 6 and 90° V6 and V8 engines. It includes 6 crankshaft and pressure plate bolts.
P4529113 Flywheel Attaching Screw Set-6-Bolt (V8 and 6-Cyl.)
CLUTCH LINKAGE
E. Clutch Fork Replacement Kits
Replacement Kits for rear-wheel-drive manual transmission clutch forks. Kits contain a clutch fork, clutch fork pivot and boot.
P4529451 Clutch fork Repair Kit-12 1/2" Approx. Length (Small Block A-Body, Except 1976)
P4529452 Clutch fork Repair Kit-10 3/4" Approx. Length (Small Block B- and E-Body)
P4529453 Clutch fork Repair Kit-10 3/4" Approx. Length (“B” Engine B- and E-Body)
F. Clutch Linkage Shaft Service Kits
Each kit contains nylon bearings, snap rings, seals, washers, lock springs, pivot ball studs and instructions.
P4529447 Clutch Linkage Shaft Service Kit (B- and E-Body)
P4529489 Clutch Linkage Shaft Service Kit (A-Body)
G. Clutch Rod Repair Kits
Each kit contains a clutch rod, nuts, washers, springs, clips
and instructions.
P4529448 Clutch Rod Kit-6.885" Overall Length (Small Block A-Body)
P4529449 Clutch Rod Kit-4.860" Overall Length (Small Block B- and E-Body)
P4529450 Clutch Rod Kit-4.880" Overall Length (Big Block B- and E-Body)
CLUTCH DISCS, PRESSURE
PLATES AND HARDWARE
A. Race Clutch Cover and Pressure Plate
Race Clutch Cover and Pressure Plate is super heavy-duty for 3100
lbs. spring load.
P4529406 Race Clutch Cover and Pressure
Plate-10 1/2" (Hemi®, Big Block, Small Block)
B. Muscle Car Pressure Plates
These Muscle Car Pressure Plates are roller designs similar to
original production units. Use with muscle car clutch discs.
P4529140 Muscle Car Pressure Plate-10 1/2",
2500 lb. Base (Dodge and Plymouth V8 Muscle Cars)
P4529141 Scalloped Muscle Car Pressure Plate-11"
(10.95"), 2500 lb. Base (1970–72 Hemi and Big Block)
C. Muscle Car Clutch Discs
Use with Mopar Performance Muscle Car Pressure Plates (P4529140 and
P4529141).
P4529136 Muscle Car Clutch Disc-10 1/2", 23
Spline (Dodge and Plymouth V8 Muscle Cars)
P4529137 Muscle Car Clutch Disc-11" (10.95"), 23 Spline (Dodge and
Plymouth V8 Muscle Cars)
P4529138 Muscle Car Clutch Disc-10 1/2", 18 Spline (Dodge and Plymouth
V8 Muscle Cars)
P4529139 Muscle Car Clutch Disc-11" (10.95"), 18 Spline (Dodge and
Plymouth V8 Muscle Cars)
D. Street/Strip Pressure Plates
P4876919 Pressure Plate-11" (10.95") (426
Hemi, 440 Big Block)
P4876920 Pressure Plate-10 1/2" (426 Hemi, 440 Big Block, 340 Small
Block)
Pilot Bearing (Not Pictured)
Pilot bearing should be replaced when servicing clutch and
throw out bearing. It should be installed with every new clutch.
P5007051 Pilot Bearing (Big Block and Small
Block)
SHIFTERS
E. Hurst Pistol Grip Shifters
Exclusively through Mopar Performance, Hurst Pistol Grip Shifters
are back! Give your 4-speed Mopar muscle car that original look and feel
it deserves with these brand-new factory reissued pistol grip shifters
from Hurst.
P4510610 Hurst Pistol Grip Shifter (All 1968–69
Non-Console, 1970 B-Body Non-Console)
P4510611 Hurst Pistol Grip Shifter (1971–74 B-Body Non-Console with
Center Armrest)
P4510612 Hurst Pistol Grip Shifter (1970–74 E-Body, 1971–74 B-Body with
Console)
P4510948 NEW! Hurst Pistol Grip Shifter (1970 B-Body with Console)
P4510614 Hurst Pistol Grip Simulated Wood Grain Insert Grips
Note: All pistol grip sticks are the bolt-in
style and are designed for use with Hurst Comp Plus shifter, part number
391–6769 (not available through Mopar).
A. RWD Clutch Release Roller Bearing and Sleeve Assembly
For all 426 Hemi® or 440 Magnum engines, it is recommended that you take the preventative measure of replacing your throw-out bearing. This RWD Clutch Release Roller Bearing and Sleeve Assembly installs easily. Applies to 4-speed transmissions with 10.50" clutch. Fits only 18-spline input shaft. It should be installed every time you replace your clutch.
P4529064 RWD Clutch Release Roller Bearing and Sleeve Assembly
B. NEW! 4-Speed Gasket Kit
Complete Rebuild 4-Speed Gasket Kit for A-833 manual
transmissions. Kit includes input seal, large rubber cone-style
rear seal and all necessary gaskets and seals.
P4510639 4-Speed Gasket Kit (A-833)
C. 4-Speed Front Bearing Retainers
Mopar Performance has re-released these previously discontinued A-833 4-Speed Front Bearing Retainers. No more scouring the salvage yards for the correct one. Whether you are swapping transmissions or restoring a legend, you can choose the correct bearing retainer for your application. Each package includes the retainer, retainer gasket and input shaft seal. Bearing retainers are identified by their outside diameter (OD), attaching bolt circle diameter (BC), and corresponding transmission input shaft.
P4529694 4-Speed Front Bearing Retainer-4.35" O.D., 3.70" BC, for 23 Spline Input Shaft (A-833)
P4529695 4-Speed Front Bearing Retainer-4.80" O.D., 3.70" BC, for 23 Spline Input Shaft (A-833)
P4529696 4-Speed Front Bearing Retainer-4.80" O.D., 4.16" BC, for 23 Spline Input Shaft (A-833)
P4529697 4-Speed Front Bearing Retainer-4.80" O.D., 4.16" BC, for 18 Spline Input Shaft (A-833)
D. Input Shaft Bearing Package
Original equipment Input Shaft Bearing Package for A-833 4-speed transmission includes bearing, snap ring and gaskets.
P4529698 Input Shaft Bearing Package-308 Bearing (A-833)
Note: 308 = 3.54" OD.
E. RWD Offset Clutch Housing Dowel Package
This dowel package contains dowels offset by 0.007", 0.014" and 0.021" (2 each).
P4120383 RWD Offset Clutch Housing Dowel Package