Mopar Performance


ENGINE STRUTS AND MOUNTS A. Engine Bobble Strut Engine Bobble Strut for manual transmissions. Increases damping force and helps reduce missed shifts. P5007028 Engine Bobble Strut (1995–99 Neon DOHC/SOHC) B. Engine Mount Engineered to help minimize engine movement during hard acceleration and cornering. The 60 durometer rubber manual transmission front mount helps reduce missed shifts. P5007027 Engine Mount (1995–99 Neon DOHC/SOHC) IGNITION AND ELECTRONICS C. Engine Controllers These emissions exempt (D-265-18) Engine Controllers are a direct replacement and will increase horsepower and torque without affecting drivability. 7,800 rpm rev limit. Requires the use of premium fuel. Manual transmission vehicles only. P5007033 PCM (1995 Neon SOHC) P5007034 PCM (1995 Neon DOHC) P5007035 PCM (1996 Neon SOHC) P5007036 PCM (1996 Neon DOHC) P5007037 PCM (1997–99 Neon SOHC) P5007038 PCM (1997–99 Neon DOHC) Note: Emissions exempt in California, Massachusetts and New York only. D. Ignition Wire Sets — 7.5 mm, Pre-Cut These high-performance Ignition Wire Sets maintain compatibility with production computers and electronics. Each package contains the high-tech style boot ends at both the distributor and plug ends of the wire. These blue wires are imprinted with the Mopar Performance name and the cylinder number. P4876510 Ignition Wire Set (1996–01 Neon SOHC) P4876511 Ignition Wire Set (Neon, PT Cruiser and 2.4L Stratus DOHC) P4876546 Ignition Wire Set (1995 Neon SOHC) E. Spark Plugs Package contains 4 Bosch Motorsports spark plugs. P4876923 Spark Plugs-Cross Reference Number RC9YC (Neon, USA 2.4L Engines) Note: 2.4L engines include Minivan, Stratus/Sebring Sedan/Breeze/ Cirrus, Sebring Convertible, Stratus Coupe/Sebring Coupe, and PT Cruiser.
	CAMSHAFTS AND CAMSHAFT TOOLS A. Camshaft Engineered exclusively for Neon, this camshaft was developed for power while maintaining reliability and idle quality. Camshaft package includes cam, front seal and cam lube. Use with valve spring P5249846. P5007030 Camshaft — 6 hp Increase, 2 hp with 2001 H.O. Engine (1995 Neon SOHC) B. Hydraulic Lash Adjusters Use these high-performance Hydraulic Lash Adjusters for improved hydraulic lash control. They are resistant to aeration. Sold in sets of 4 (2 sets required per engine). P5007440 Hydraulic Lash Adjusters (1995–99 Neon DOHC, 2.4L DOHC Engines) Note: 2.4L engines found in the following vehicles: Minivan, Stratus/Sebring Sedan/Breeze/Cirrus, Sebring Convertible, Stratus Coupe/Sebring Coupe and PT Cruiser. INTAKE MANIFOLD COMPONENTS C. EGR Block-Off Plate Kit Lightweight, 6061-T6 anodized aluminum Block-Off Plate Kit will remove EGR valve for racing purposes only. Includes head and manifold plates with gaskets. P5007276 EGR Block-Off Plate Kit (1995–99 Neon SOHC/DOHC) VALVE COVERS D. NEW! Carbon Fiber Valve Cover Add even more excitement under your hood with a carbon ﬁber valve cover. Mopar Performance’s injection-molded carbon ﬁber valve covers offer great sealing performance using stock seal and anodized 6061 aluminum ﬁttings. Twill woven materials give the valve covers a stunning carbon ﬁber look. These are the lightest valve covers that can be made without sacriﬁcing the structural integrity necessary for race cars and high-performance street machines. P4510539 Carbon Fiber Valve Cover (2001–05 Neon SOHC)

VALVES AND VALVE HARDWARE A. Stainless Steel Valves Stainless steel for improved durability. Oversize diameter heads for improved airﬂow and performance. Intake head diameter is 34.00 mm, vs. 33.24 mm stock. Exhaust head diameter is 29.30 mm, vs. 28.70 mm stock. They feature a swirl polished underhead area and a chromed stem and hardened tip. No ﬂat or ski-jump areas on underhead area. Sold individually. P5007507 Stainless Steel Valve-Intake, 34.00 mm Diameter (Neon SOHC) P5007508 Stainless Steel Valve-Exhaust, 29.30 mm Diameter (Neon SOHC) B. Valve Springs High-pressure valve springs can be used on exhaust and intake valves for all high-performance applications. They feature a shorter fully compressed height and allow for increased valve lift. Springs maintain spring load at higher rpms. A must for high performance cams. Sold individually. P4876636 Valve Spring (1995–99 Neon DOHC) P5249846 Valve Spring (Neon SOHC) OILING COMPONENTS C. Windage Tray Neon Windage Tray provides better engine lubrication by reducing windage and aeration at higher engine speeds. Includes mounting hardware and pan gasket. P5007278 Windage Tray AIR SYSTEMS D. Air Filter Mopar Performance Air Filters are constructed with factory tight seals, engineering level polyurethane, deep 4-ply pleats of oiled cotton gauze and 2-layer screen. This ﬁlter offers high ﬂow and low restriction, better throttle response and increased ﬁltration and horsepower. Filters are washable and reusable and come pre-oiled. P4510478 Air Filter (2003 SRT4, 2001–03 Neon) E. Cold Air Intake Systems Heat up your Neon with a steady ﬂow of cold air! These bolt-on systems are designed to direct cooler outside air through a directional cone ﬁlter and funnel, directly into the intake manifold. These kits provide noticeable horsepower and torque gains under varying atmospheric conditions. Kits include all mounting hardware and a pre-oiled, washable/reusable ﬁlter. P5007833 Cold Air Intake System (2000–03 Neon SOHC) P5007031 Cold Air Intake System (1995–99 Neon SOHC/DOHC MTX)
	SUSPENSION COMPONENTS A. NEW! Rear Tension Strut Kit Rear Tension Struts feature a high-durometer bushing material designed for heavy duty and competition use. The revised design results in improved toe stability (reduced bump-steer), which virtually eliminates rear wheel hop under heavy braking. Provides more positive suspension control for improved driver feedback and dynamic stability. P4510826 Rear Tension Strut Kit-Left and Right (2003–05 SRT4, 2000–05 Neon) B. Performance Struts These rebound adjustable performance Struts will improve the handling and performance of your Neon. Precision manufactured struts are the same as those found on the 1995–99 Neon ACR. Meets SCCA Club rules. Includes all mounting hardware. Sold individually. P4876812 Front Strut (1995–99 Neon) P5007000 Rear Strut (1995–99 Neon) C. Coil Springs These Mopar Performance Coil Springs will add a new dimension to your car’s handling and performance. Reduce body roll and attack corners with conﬁdence on the street and track. Upgrade base model vehicles to ACR/RT level, and upgrade ACR/RT models to higher levels. Select spring sets lower car as noted. Sold in pairs. P5007003 High Rate Autocross Coil Springs-Front, 225 lbs./In., 1" Lower Ride Height (1995–99 Neon) P5007004 Extra-High Rate Autocross Coil Springs-Front, 310 lbs./In., 1" Lower Ride Height (1995–99 Neon) P5007005 High Rate Autocross Coil Springs-Rear, 185 lbs./In., 1" Lower Ride Height (1995–99 Neon) P5007006 Extra-High Rate Autocross Coil Springs-Rear, 230 lbs./In; 1" Lower Ride Height (1995–99 Neon) D. Strut Adjuster Knob Use to adjust production ACR and Mopar Performance ACR struts. Same as provided in ACR glove box. P5007269 Strut Adjuster Knob (1995–99 Neon ACR)
SUSPENSION UPGRADES The Stage 1, 2 and 3 Mopar Performance Suspension Components were produced by a team of Mopar and KW Suspension engineers using DaimlerChrysler specs, logging hundreds of hours of real world and track testing time to ensure optimal performance. A. NEW! Stage 1 Anti-Sway Bars Mopar Performance Anti-Sway Bars are made from high-quality bar material that ensures durability and heightens performance, ride and handling by virtually eliminating body roll, helping to keep all four tires ﬁrmly on the pavement. An exclusive adjustable rear sway bar allows you to tune in the system to your speciﬁc driving needs! P4510457 Stage 1 Anti-Sway Bar Kit — Front and Rear (2000–05 Neon) B. NEW! Stage 1 Performance Springs These Performance Springs are made of high-tensile spring material that ensures durability and heightens spring performance without bind. These factory-produced springs provide a 25 mm drop from the stock ride height. P4510460 Stage 1 Performance Springs — Front and Rear (2000–05 Neon) C. NEW! Stage 2 Coilover Suspension Kit Get ready for a whole new level of performance! This Coilover Suspension Kit provides your vehicle with better handling and ride characteristics than any other aftermarket suspension system available today! The Stage 2 Coilover Suspension Kit utilizes cutting edge technology born on the track and raised on the street. This kit allows you to lower your vehicle within a speciﬁed range using adjustable aluminum spring perches to suit your driving needs. It is height adjustable from 0–30 mm lower than factory, and includes ﬁxed-valve dampers. Features: • Easy-adjust stainless steel impregnated composite perches • Stock height and down lowering range • High-quality, high-tensile racing springs • Special ventilation and sealing system • Hardened chromium-plated piston rods • Pistons with V-shaped Teﬂon seals • Strut and shock housings in INOX-line stainless steel • Inﬁnitely adjustable within adjustment parameters • Shortened struts for increased travel • Trapezoidal adjustment threads for simple height adjustment • Elastomer bump stops with integrated dust boot protection P4510451 Stage 2 Coilover Suspension Kit (2000–05 Neon)
INOX Technology Stage 2 and 3 Kits feature new INOX Stainless Steel technology exclusive to Mopar Performance and KW Suspensions. After 418 hours of testing (salt water spray), INOX Coilover Suspension Struts constructed of stainless steel were clearly superior to the galvanized versions in terms of corrosive resistance, and were still functioning perfectly after testing.
A. NEW! Stage 3 Coilover Suspension Kit The Stage 3 Coilover Kit includes all the features of the Stage 2 Kit. In addition, the Stage 3 Kit allows drivers to adjust the damper setting of the suspension system for the ultimate in personalization. The adjustable rebound damper gives drivers the ability to adjust the vehicle’s pitch and roll to their driving preferences and needs, from the street to the track. The Stage 3 Kit is height adjustable and rebound adjustable from 20% under to 50% over Stage 2 settings. Rebound adjustment takes place via an adjustment screw at the end of the piston rod, and primarily affects the low and midrange rebound dampening. Features: • External adjustable rebound damper • Stock height and down lowering range • Easy-adjust stainless steel-impregnated composite perches • High-quality, high-tensile racing springs • Special ventilation and sealing system • Hardened chromium-plated piston rods • Pistons with V-shaped Teﬂon seals • Strut housings in INOX-line stainless steel • Inﬁnitely adjustable within adjustment parameters • Shortened struts for increased travel • Trapezoidal adjustment threads for simple height adjustment • Elastomer bump stops with integrated dust boot protection P4510587 Stage 3 Coilover Suspension Kit (2000–05 Neon)
	TRANSAXLE COMPONENTS A. Limited-Slip Differential Quaife automatic torque-biasing (ATB) Limited-Slip Differentials are high-quality components that help make your ride even quicker. The unique design improves handling and steering, and powers both drive wheels under nearly all conditions. Internal components sense which wheel has better grip and biases more power to that wheel. P5007382 Limited-Slip Differential (2001–05 Neon T-350 MTX and PT Cruiser Non-Turbo) B. Short-Throw Shifter The Mopar Performance Short-Throw Shifter offers a dramatic improvement in shifting performance, due in large part to reduced shifter travel or “shifter throw.” In performance driving scenarios, the additional seconds-or fractions of a second-a factory equipped shifter takes to go from one gear to another may result in slower lap times. It features revised geometry, which improves shifter feel, narrows the neutral gate and shortens the shift throws. P4510485 Short-Throw Shifter-Direct Bolt-On, Self- Contained Unit (2003–05 SRT4, 2000–05 Neon) Note: Neon factory shift boot and knob will not ﬁt this part. One option is to use the SRT4 Shift Knob (0XF701ZAAA) and Shift Boot (05029257AA). C. Clutch Installation Kit Components required for initial installation of P5007392 clutch in place of conventional clutch and ﬂywheel. Not required in vehicles already equipped with production modular clutch assembly. Also not required again once P5007392 has been installed. Kit includes drive plate and backing plate, drive plate-to-crankshaft attaching bolts, and upper and lower dust shields. P5007435 Clutch Installation Kit (1995–99 Neon) WHEEL COMPONENTS D. Hub and Bearing Kit This kit upgrades standard hubs and bearings to service Neon ACRs. Upgrade is recommended for non-ACR Neons used for racing purposes. ACR hubs and bearings should be replaced after 12 on track hours. Kit includes 1 hub and 1 bearing. Same as production 1995–99 ACR. P5007314 Hub and Bearing Kit (1995–99 Neon ACR)